Hondata System Features Table

The s100 system has the following features:

• Fits inside the ECU. No external wiring.
  
• Speed limiter removed (if applicable).
  
• Tunable fuel and ignition tables.
  
• Expanded fuel & ignition tables for boost.
  
• Expanded rpm fuel & ignition tables.
  
• A/C cutout.
  
• VTEC control (non user adjustable).
  
• Rev limiter (non user adjustable).
  
• Nitrous Control.
  

__________________________________________________________________________________
Discontinued in January of 2008.

The s200 system consists of an interface box which connects to a modified stock ECU. The s200 replaces the Stage 2/3/4 systems.

The s200 system has the following features:

• Speed limiter removed (if applicable).
  
• Tunable fuel and ignition tables.
  
• Expanded fuel & ignition tables for boost.
  
• Expanded rpm fuel & ignition tables.
  
• A/C cutout.
  
• Shift light.
  
• VTEC control.
  
• Adjustable rev limiter.
  
• Launch control.
  
• Full throttle shift.
  
• Nitrous Control
  
• Datalogging with HondaLogger software.
  
• Datalogging with Palmlog software (no longer supported)
  
• ROM Editor tuning software.
  

_________________________________________________________________________________

The s300 is a plug in module to the factory Honda Engine Computer (ECU) which vastly expands the capabilities of the factory ECU. Forced induction, datalogging, real time updating of parameters, engine protection are but a few of the s300 features.

S300 Main features:

• Fits inside the ECU
  
• Made in USA
  
• Built on the proven s100/s200 code base
  
• USB connection for speed and compatibility
  
• SManager Windows based software for parameter & table editing, calibration uploading and datalogging.
  
• Real-time updating of ECU
  
• Built in calibrations for common engine combinations
  
• Built in datalogging to a laptop
  
• On board datalogging memory (2 MB memory, 20-60 minutes datalogging)
  
• Adjustment for different sized injectors, with overall fuel trim.
  
• Configurable for any MAP sensor (to at 5 Bar and above)
  
• TPS based table lookup for ITBs
  
• Engine protection from over boost.
  
• Expanded fuel and ignition tables, both in rpm and load, to 60 lbs boost and 11,000 rpm (these are not the upper limits)
  
• Launch control with anti-lag
  
• Full throttle shift
  
• Three multi purpose outputs for nitrous control or similar
  
• Supports lambda tracing from a wideband o2
  
• PWM output for boost control
  
• Dual tables for high/low octane calibrations etc.
  
• Two analog inputs for wideband, EGTs etc.
  

SManager editing software features:

• High and low speed 24 x 20 ignition and fuel tables for correct VTEC tuning
  
• Injector size fuel trim
  
• Fuel trim for starting, throttle tip in and individual cylinder trim
  
• Rev limiter with fuel cut or fuel and ignition cut
  
• Launch control with anti-lag
  
• Full throttle shift
  
• Adjustable VTEC window with load and throttle control
  
• Secondary intake runner control
  
• Adjustable idle speed
  
• MAP sensor type and calibration
  
• Adjustable boost cut with hot and cold settings
  
• Shift light
  
• Closed loop control
  
• Air temperature compensation
  
• Water temperature compensation
  
• Fuel and ignition correction based on gear
  
• A/C shutoff conditions
  
• Closed loop
  
• Three general purpose outputs for nitrous control, quad boost control or similar
  
• On board datalogging trigger conditions
  

The s300 uses different connecting pins in the ECU from the s100/s200, and also has a slot cut in the side for the USB connector, so the ECU must be modified for use with the s300. The s300 is made to fit in a full frame ECU case (US and most markets), so will not fit in a JDM ECU case.

Real Time Programming
The s300 can be updated in real-time with the engine running without affecting the operation of the vehicle. This means that calibrations and changes can be uploaded to the ECU very quickly (2 seconds for a new calibration, a fraction of a second for anything else), without interrupting the operation of the engine. Changes made in the SManager software are uploaded to the ECU instantly and you can see the effect immediately. The s300 does not use an EEPROM or equivalent, so you never need to open the ECU to change chips nor 'burn' ROMs. No EPROM programmer is necessary - you just need a laptop with USB port.
Note that this the only true real-time update available for Honda ECUs. Any portion of the ECU (including the whole ROM) may be quickly updated with the engine running, without the engine stalling or going into limp mode.



Datalogging
The s300 has datalogging to the SManager software built in via the USB port. Using a laptop the various ECU sensors can be datalogged, viewed, graphed and saved for later analysis.
Additionally the s300 has on board flash memory which allows a datalog recordings to be made without a laptop, for later access and download to a laptop. Multiple recordings can be made and stored in the s300 for a total of around 40 minutes of total datalogging time. An external switch can be used to start and stop recordings, or engine conditions can trigger recording. For instance in a drag race, the s300 can be set to start recording once the rpm is bought up to near launch rpm and automatically stop once past the traps and the rpm drops below a certain level.

MAP Sensor Compatibility

Any linear MAP sensor can be used, using a scalar and offset to translate the MAP sensor characteristics into pressure. Popular MAP sensor settings are built in for ease of setup. To do this you will need the map sensor calibration numbers from the manufacturer of the sensor.


Thank Hondata for the provided info